Chapter 2

Flight Mechanics

Why an airplane returns to level flight on its own, why a steeper bank raises the load on the wings and the stall speed, and how far an airplane can glide with the engine out.

scroll to begin ↓

Topic 2.1

Stability & Control

Imagine an airplane flying straight and level when a gust of wind briefly pushes its nose upward. What happens after the gust passes? A stable airplane tends to return toward its original pitch attitude, the angle of its nose relative to the horizon. This tendency is called static stability. An airplane that has no tendency to return or move farther away is neutrally stable, while one that continues moving farther from its original attitude is unstable. Stability describes the airplane's natural response to a disturbance; it does not mean the airplane will immediately return to its original position. The airplane may pitch up and down several times before settling. Aerodynamic damping, caused by the air resisting that motion, helps those oscillations gradually die out.

One of the most important factors affecting pitch stability is the location of the center of gravity (CG), the point where the airplane's weight effectively acts. Its position is compared with the neutral point, the location where the airplane has no natural tendency to increase or decrease its pitching motion after a small change in angle of attack. When the CG is ahead of the neutral point, the airplane is generally stable in pitch. For example, if a gust raises the nose, the resulting increase in lift creates a restoring pitching moment that tends to bring the nose back down. If the CG moves behind the neutral point, that restoring tendency disappears. A nose-up disturbance can instead create a pitching moment that raises the nose even farther.

The static margin measures how far the CG is ahead of the neutral point, relative to the wing's mean aerodynamic chord, which is its average front-to-back width. A positive static margin means the CG is ahead of the neutral point and the airplane has positive pitch stability. A larger positive margin generally means a stronger restoring tendency. A static margin of zero means the CG is at the neutral point, while a negative margin means the CG is behind it and the airplane is unstable in pitch. For example, if the neutral point is at 32% of the chord and the CG is at 25%, the static margin is 7%.

Every airplane has approved forward and aft CG limits because both extremes create handling problems. If the CG moves too far aft, the airplane can lose its natural pitch stability, making it harder to control. If the CG moves too far forward, the airplane may become difficult to pitch up, especially during the landing flare, when the pilot raises the nose just before touchdown. The elevator helps the pilot control pitch by changing the aerodynamic force on the tail. This also changes the airplane's trim attitude, the attitude it settles into when the controls are held fixed. The amount of aerodynamic force on the tail depends strongly on airspeed, so the airplane's response to a disturbance can change as it flies faster or slower.

In the simulation, the blue marker below the airplane is the CG, the red marker is the neutral point, and the shaded area between them is the static margin. With the CG at 25%, press Bump the Nose and watch the pitch trace swing and settle back to the dashed trim line. Move the CG aft of the neutral point, past 32%, and bump again to see the pitch diverge. Then raise the airspeed or move the elevator and compare the response.

Static Margin
\(SM = \frac{x_{NP} - x_{CG}}{c}\)
SM = static margin (as a fraction of the chord) xNP = neutral point position (measured back from the wing’s front edge) xCG = center of gravity position (measured the same way) c = mean aerodynamic chord (the average front-to-back width of the wing)
A positive static margin means the airplane tends to return to its trimmed attitude after a disturbance.
25%
0°
80 kt

Topic 2.2

Turns & Bank Angle

An airplane turns by banking its wings. When the wings tilt, the lift force tilts with them because lift acts perpendicular to the wing. Instead of pointing straight upward, lift now has two components: an upward component that supports the airplane's weight and a sideways component that pulls it toward the center of the turn. The sideways force is what changes the airplane's direction. The bank angle, φ (the Greek letter phi), measures how far the wings are tilted from level.

In a level turn, the airplane must maintain enough upward lift to balance its weight. However, as the bank angle increases, a smaller portion of the total lift points upward. The airplane must therefore produce more total lift to keep the same altitude. The relationship can be described using the cosine of the bank angle. Cosine tells us what fraction of the total lift acts upward: at 0° bank, all of the lift points upward, while at 60° bank, only half does. This means the wings must produce twice as much total lift to support the airplane. The ratio of total lift to weight is called the load factor, n. In straight-and-level flight, the load factor is 1 g. At 30° of bank it is about 1.15 g, at 45° it is about 1.41 g, and at 60° it reaches 2 g.

Producing this extra lift requires the pilot to increase the wing's angle of attack, usually by applying back pressure on the controls. As explained in Topic 1.3, increasing the angle of attack produces more lift, but it also increases drag. The pilot may need to add power to maintain airspeed. The higher load factor also affects everyone on board: at 2 g, the airplane and its occupants experience twice their normal weight. This additional load is important because it also raises the speed at which the wing stalls.

The stall speed increases with the square root of the load factor. For example, a load factor of 2 raises stall speed by a factor of √2, or about 41%. An airplane that stalls at 50 knots in level flight would therefore stall at about 71 knots in a level 60° banked turn. The wing still stalls at the same critical angle of attack; it simply reaches that angle at a higher airspeed because it must produce more lift. This is why an airplane can stall at a speed well above its usual straight-and-level stall speed when it is heavily loaded in a turn.

In the simulation, the pink arrow is weight, and the green dashed arrow is the upward part of lift, which stays the same length. The blue dashed arrow is the sideways part, labeled turning force, and the solid green arrow is the total lift. Raise the bank angle and watch the total lift arrow grow while the load factor and stall speed readouts rise. Compare 30°, 45°, and 60°, then continue to 75°, where the load factor is nearly 4.

Load Factor
\(n = \frac{1}{\cos(\phi)}\)
n = load factor, the ratio of lift to weight (in g’s) φ = bank angle (the tilt of the wings from the horizon) cos φ = cosine of the bank angle (1 at 0°, 0.5 at 60°)
At 60° bank, n = 2: the wings must produce twice the airplane’s weight in lift.
30°

Topic 2.3

Best Glide

When the engine stops, an airplane does not fall. It glides. With no thrust, it settles into a gentle downhill path, giving up height to keep moving forward, much like a bicycle coasting down a hill. The flatter that path, the farther the airplane travels before it reaches the ground.

How flat the path is can be measured by the glide ratio, the distance the airplane travels forward for each unit of height it loses. A glide ratio of 9 to 1 means 9 feet forward for every 1 foot down. From 2,500 feet in calm air, that is 22,500 feet, or about 3.7 nautical miles.

The glide ratio comes down to how well the wing does its two jobs. Lift holds the airplane up, and drag pulls it back and costs it height. A wing that makes a lot of lift for very little drag holds the airplane up while barely slowing it, so the path is flat. A wing that makes more drag for the same lift gives a steeper path. Lift divided by drag is called the lift-to-drag ratio, and in calm air the glide ratio equals it, as the equation below shows. A lift-to-drag ratio of 9 means the wing makes 9 times as much lift as drag.

How fast the airplane flies changes the lift-to-drag ratio, because drag comes from two sources. At high speed, the air rushing past creates a lot of drag. At low speed, the wing has to tilt to a larger angle of attack to keep holding the airplane up, and that costs drag too (Topics 1.2 and 1.3). Between the two there is a speed where drag is lowest for the lift needed. That is the best glide speed, and it gives the most distance in calm air. Faster or slower, the glide gets steeper and altitude is wasted. For a real airplane, the best glide speed is listed in its flight manual.

Wind changes how far the airplane gets over the ground, but not how it glides through the air. A headwind slows its progress over the ground, so it covers less ground for each foot it descends, and a tailwind does the opposite. In a headwind, flying a little faster than best glide speed gives more distance over the ground, because it trades a small loss of glide ratio for less time spent being pushed back.

In the simulation, the marker where the dashed path meets the ground is the touchdown point, and FIELD marks a field 3.0 nautical miles away. Both turn green when the airplane reaches the field and red when it falls short. The graph at the right shows glide ratio against airspeed, with a dot at the current airspeed. With the wind calm, move the airspeed away from best glide and watch the glide ratio and range fall. Then add a headwind or tailwind and see what changes.

Glide Ratio
\(GR = \frac{L}{D}\)
GR = glide ratio: feet traveled forward for every foot of height lost L = lift, the upward force from the wings D = drag, the backward force from the air
In still air, a glide ratio of 9:1 means 9 feet forward for every 1 foot down.
68 kt
2,500 ft
Calm

Chapter 2 Complete

You've covered core principles of how forces control an aircraft.

Next, where thrust comes from: the engine, the propeller, and the effect of air density.