Chapter 3
How an engine turns fuel into power, how a propeller turns that power into thrust, and how altitude and temperature change takeoff performance.
Topic 3.1
A piston engine turns the energy stored in fuel into the rotating motion that drives the propeller. Inside each cylinder, a piston moves up and down. A connecting rod links the piston to the crankshaft, which converts that back-and-forth motion into rotation. The engine repeats a four-stroke cycle to keep the crankshaft turning. During the intake stroke, the piston moves down while the intake valve opens, drawing an air-fuel mixture into the cylinder. During the compression stroke, both valves close and the piston moves up, squeezing the mixture into a smaller space. A spark plug then ignites the mixture. The expanding hot gases push the piston down during the power stroke, transferring energy to the crankshaft. Finally, during the exhaust stroke, the exhaust valve opens and the piston pushes the burned gases out. The cycle then starts again. Each complete cycle takes two revolutions of the crankshaft, but only one of the four strokes directly produces power.
The amount of power an engine can produce depends partly on how much air enters its cylinders. Fuel must be mixed with that air in the correct proportion for combustion. More air allows more fuel to burn, releasing more energy during the power stroke. This is why the amount of air entering the engine matters so much: the engine cannot produce more power simply by adding fuel if there is not enough air to support combustion.
Two factors determine how much air the engine takes in over time: how much enters during each cycle and how quickly those cycles happen. Manifold absolute pressure (MAP) measures the pressure of the air in the intake manifold, the passage that distributes air to the cylinders. Higher MAP generally means denser air entering each cylinder. Volumetric efficiency, represented by ηv (the Greek letter eta), describes how effectively the cylinder fills with air compared with the amount it could hold at the manifold pressure. RPM measures how many times the crankshaft rotates each minute. Since each cycle takes two crankshaft revolutions, higher RPM means more intake cycles occur each minute. Together, these factors determine the engine's indicated power: the power developed inside the cylinders before losses from friction and other mechanical inefficiencies.
The throttle controls how much air enters the engine by restricting airflow into the intake manifold. When the throttle is partly closed, manifold pressure drops, less air enters each cylinder, and the engine produces less power. Opening the throttle allows more air in and increases MAP. At full throttle, a normally aspirated engine can only draw in air at approximately the pressure available outside the airplane; it cannot compress the intake air above that pressure. Because atmospheric pressure and air density decrease with altitude, the engine takes in less air as it climbs. Even at full throttle, a normally aspirated engine therefore produces less power at higher altitudes.
In the simulation, one cylinder runs through the four strokes, and the panel at the right highlights the active stroke. The Air per Cycle gauge shows how much air each cylinder draws in, and Power Output combines that with RPM. Lower the throttle and the cylinder fills with fewer particles. Lower the air density, which stands in for climbing to a higher altitude, and the particles become fewer and fainter while power drops. Raise the RPM and the cycle runs faster.
Topic 3.2
A propeller blade works much like a small wing that spins around the engine. Each section of the blade has an airfoil shape and produces an aerodynamic force as it moves through the air. However, unlike an airplane wing, a propeller blade experiences two sources of motion at once: it moves around the engine as the propeller rotates, and it moves forward with the airplane. These two motions combine to create the relative wind, the airflow the blade experiences. The faster the airplane moves forward, the more the relative wind tilts away from the plane of rotation, the flat circle traced by the spinning blades. The blade's pitch is the angle between its chord line, an imaginary line from its front edge to its back edge, and the plane of rotation. Its angle of attack is approximately the blade pitch minus the angle of the relative wind. For example, a blade section rotating at about 300 knots while the airplane moves forward at 80 knots experiences a relative wind tilted by about 15°. If its blade pitch is 22°, its angle of attack is therefore about 7°.
This changing angle of attack creates a problem for propellers with a fixed blade pitch. At low forward speeds, the relative wind is tilted only slightly, so a blade with a low pitch can produce an effective angle of attack. As the airplane speeds up, the relative wind tilts farther, reducing the blade's angle of attack. If it becomes too small, the propeller produces very little thrust. A blade with a higher pitch has the opposite problem: it can work well at cruise speed, but at low forward speeds its angle of attack may become too large, causing the blade to stall. A constant-speed propeller solves this problem by allowing the blade pitch to change while the propeller spins. A governor adjusts the pitch to maintain the RPM selected by the pilot, using a finer pitch at low speeds and a coarser pitch as forward speed increases. This helps the blades maintain an effective angle of attack across a wider range of flight conditions.
A propeller produces thrust by accelerating air backward. As the blades rotate, their aerodynamic force pushes air rearward. By Newton's third law, the air exerts an equal and opposite force on the propeller, pushing the airplane forward. The amount of thrust depends on two things: how much air passes through the propeller each second and how much the propeller increases that air's speed. This relationship is described by T = ṁ × Δv. The symbol ṁ, pronounced "m-dot," represents the mass of air passing through the propeller each second, while Δv represents the increase in that air's speed. For example, if a propeller accelerates 130 kilograms of air per second by 10 meters per second, it produces about 1,300 newtons of thrust, or roughly 290 pounds. The propeller's blades create the aerodynamic forces that accelerate the air, and the resulting reaction pushes the airplane forward.
In the simulation, the arrow at the propeller shows thrust, and the graph at the right shows thrust against airspeed for the current RPM and pitch, with a dot at the current airspeed. The simulation uses the blade section 70% of the way out, and when its angle of attack exceeds 15° the blade stalls: the warning appears and the air behind the propeller turns red and unsteady. Set the airspeed to 0 with the default pitch and watch the blade stall, then lower the pitch to recover. With a low pitch, raise the airspeed and watch the thrust fall to zero.
Topic 3.3
Air density affects how well an airplane's engine, propeller, and wings perform. Density depends on both air pressure and temperature. As altitude increases, atmospheric pressure decreases, making the air less dense. Higher temperatures also make air less dense because the air expands. This means an airport at a high elevation or on a particularly hot day can have thinner air than an airport at sea level on a cool day. Density altitude describes this effect by expressing the current air density as an equivalent altitude in the standard atmosphere. In other words, it tells a pilot how high the airplane would have to fly in standard atmospheric conditions to experience the same air density. A hot day can therefore make an airport behave as though it were at a much higher elevation.
A common approximation for calculating density altitude is DA = PA + 120 × (OAT − ISA). Pressure altitude (PA) is the altitude indicated when the altimeter is set to the standard pressure of 29.92 inches of mercury. Outside air temperature (OAT) is the actual temperature, while ISA is the standard-atmosphere temperature at that pressure altitude. In the standard atmosphere, temperature starts at 15°C at sea level and decreases by approximately 2°C for every 1,000 feet of altitude. The difference between the actual temperature and the standard temperature is called the temperature deviation. For every degree Celsius that the actual temperature is above standard, density altitude increases by approximately 120 feet. For example, at a pressure altitude of 5,000 feet, the standard temperature is about 5°C. If the actual temperature is 30°C, the temperature is 25°C above standard, giving a density altitude of approximately 8,000 feet.
Higher density altitude reduces takeoff performance in three ways. First, the engine takes in less air during each cycle, reducing the amount of fuel it can burn and lowering its power output (Topic 3.1). Second, the propeller accelerates less mass of air each second, reducing the thrust it produces (Topic 3.2). Third, the wings need a higher true airspeed to produce the lift required for takeoff. The lift equation from Topic 1.3 explains why: when air density decreases, the airplane must move faster through the air to produce the same lift. Together, these effects mean the airplane accelerates more slowly and needs to travel farther before reaching liftoff speed. A simplified estimate suggests that takeoff distance increases roughly with the inverse square of the density ratio. For example, at a density altitude of 8,000 feet, the density ratio is about 0.79, giving an estimated takeoff distance roughly 1.6 times the sea-level distance. This is only an approximation. Actual takeoff distance depends on the airplane, runway, wind, and other conditions, so pilots must use the performance charts in the airplane's flight manual when planning a takeoff.
In the simulation, the panel at the top left shows density altitude, density ratio, and takeoff distance, and the graph at the right shows takeoff distance against temperature at the current field elevation, with the dashed line marking the 2,000-foot runway. The simulation treats field elevation as pressure altitude and uses an illustrative sea-level baseline of 900 feet. At a field elevation of 10,000 feet, raise the temperature and watch the liftoff marker pass the runway end once it rises above about 20°C.
Course Complete
Each maneuver your instructor teaches has a physical reason behind it, and you now know the basic principles behind many of them.